Liquid Epoxy Damp Proof Membrane 5kg (Metal Tin)

A two-component, solvent-free, low odour liquid epoxy DPM that is tolerant of residual moisture in concrete floors. When dry, it creates a new damp proof layer across the floor surface protecting the future covering from damp.

Read More

Availability: >In stock


RRP £87.50 Ex VAT
£65.00 Ex VAT £78.00 Inc VAT

Liquid Epoxy Damp Proof Membrane - 5kg

This Epoxy DPM is a two-component, solvent free, low odour epoxy resin membrane that is tolerant of residual moisture in concrete floors. This enables earlier access onto the floor for the application of screeds, coatings and other floor coverings including tiles, vinyl, wood and carpets. Our epoxy DPM has good chemical resistance to mild chemical attack, but is designed to be over-coated with other resin finishes.

Our Epoxy DPM can be used on concrete floors and fine concrete screeds, of not less than 50mm thick in the case of un-bonded screeds. The surface should be of sufficient quality and mechanical strength to ensure an even coating.

The product can also be applied to polymers, screeds and certain types of smoothing under-layments, as long as these are well bonded. These under-layments must be stable to the effects of water. If not, then the concrete floor must contain an integral damp. proof membrane to prevent further ingress of water from the ground.

If you are laying the epoxy onto a concrete surface with an ineffective damp proof membrane or where there isn't one at all, you need to consider the possibility of hydrostatic pressure. By creating a barrier layer, you will direct the pressure/water flow elsewhere.

Liquid Epoxy DPM Application

Mixing Instructions

Open each tin and add the smaller container to the larger container and mix with a mixing paddle in the end of a power drill at a slow speed. Ensure the product is thoroughly mixed, is consistent and has no streaks. The minimum mixing time is 3 minutes.

Important Note: Once the two components are mixed, the Epoxy DPM must be laid onto the concrete within 10 - 25 minutes depending on substrate and air temperature. The warmer the temperature the quicker the product will start to go off.

Application Instructions

Apply the mixed material using a high quality roller. Epoxy Damp Proof Membranes are always installed in a minimum of two coats 24 - 48 hours apart.

For floors with a high RH Reading above 92% three coats are required. Once mixed, the product has a usable life of approximately 10-25 minutes maximum depending on site conditions. Past this point the product cannot be used for further coats.

Epoxy Damp Proof Membrane is applied at 200 micron thickness (0.2mm) per coat. Although the epoxy will tolerate slight variations to this, we would not advise that it is applied above 0.5mm thickness as this could result in bubbling and curing issues.

Liquid Epoxy Damp Proof Membrane dries clear, if you require a coloured finish we recommend a coat of Epoxy Resin Floor Coating HB after Liquid Epoxy Damp Proof Membrane has been installed.

If you wish to lay tiles or adhere any further coatings including self-levelling compounds on top of this coating we advise that you blind the final coat of Liquid Epoxy Damp Proof Membrane with Fine Quartz Aggregate 30 minutes after laying the coat to provide a key for the tile adhesive or grout to bond to.

Permagard – Providing Solutions. Inspiring Confidence.

If you need any technical advice on epoxy flooring or laying an epoxy DPM then give our expert team a call on 0117 982 3282.


  • Improved formulation
  • Convenient packaging
  • Easy application
  • Application onto substrates with hygrometer readings up to 97%
  • Solvent free
  • Low odour
  • Excellent adhesion
Model: ERDPMT5
Manufacturer: Permagard
Packaging: 2 components supplied in metal tins.
Size: total weight of two components is 5kg
Dilution: Mix the two components together to activate the product for use.
Coverage: Each 5kg unit will cover between 18-20m² per coat (minimum of 2 required) dependent on substrate condition.
RAL Award Certificate No: Clear
Country of Manufacture: United Kingdom

Need more information?

Speak to our technical experts.
0117 982 3282

Be the first to review this product

How do you rate this product?

1 1 star
2 2 star
3 3 star
4 4 star
5 5 star